Update N900XXUEBOK2 Firmware ON GALAXY Note 3 SM-N900 to Android 5.0 Lollipop


N900XXUEBOK2
Android 5.0 is the new official firmware update for the GALAXY Note 3 SM-N900 and now it is available and you can download it from Galaxy Rom Website and get help to updating and installing it with
our Complete Tutorial. 

There
are several ways to install XXUEBOK2 Android 5.0 Lollipop on your
GALAXY Note 3 SM-N900 so, read this tutorial and you will be able to
get the new update easily.

We recommended that you
always update your Android OS on your Android Device because it will
improve the performance of your Phone.
Note: Read this
tutorial carefully and do it on you own risk. Galaxy Rom
Website Team are not responsible for any damage caused on your phone ,
so be careful when you do anything and make sure that you are doing it
with the right way.

Please read the notes before installing the Official ROM/Firmware Lollipop 5.1.1 Phone GALAXY Note 3 SM-N900

    Update N900XXUEBOK2 Firmware ON GALAXY Note 3 SM-N900 to Android 5.0 Lollipop

  1. Installation of this
    ROM/Firmware on your own risk and as we said Galaxy Rom
    Website Team are not responsible for any damage caused on your phone .
  2. This ROM/Firmware for GALAXY Note 3 SM-N900  only ,So don’t install it on any other
    Samsung device .Check your device model and be sure that is matched the
    same Model here in this tutorial . Go to Settings > About Phone >
    Model Number .
  3.  Make a backup for
    your personal data to avoid data losing.
  4.  Make sure that your
    battery is 50% at least before starting the update process.
  5.  Don’t move or remove the USB
    cable during the Firmware installation Process .
  6.  Attached images are
    examples only, so you may find some difference, but all steps are same at
    all.
  7.  Enable USB Debugging Mode
    on your Samsung device by going to developer options ( If you can’t find
    Developer Options you must show it by going to Settings > About phone
    then tab 7 times on Build Number and you will get message tell you that
    the developer options are enabled , See the image below).

    Enable USB Debugging Mode on your Samsung device by going to developer options ( If you can’t find Developer Options you must show it by going to Settings > About phone then tab 7 times on Build Number and you will get message tell you that the developer options are enabled , See the image below).
  8. All the above notes are very important and you must follow
    them before proceeding the installation process.


Rom Official Firmware Details for Lollipop 5.1.1 GALAXY Note 3 SM-N900

Firmware:Details
Model:SM-N900
Model Name:Samsung GALAXY Note 3 SM-N900
Version:Android 5.0
PDA:N900XXUEBOK2

Download Official Firmware GALAXY Note 3 SM-N900

Singapore  :N900XXUEBOK2_N900OLBEBOJ1_XSP

Sri Lanka  :N900XXUEBOK2_N900ODDEBOB2_SLK

Nepal:N900XXUEBOK2_N900ODDEBOB2_NPL

After
the download you can Now, follow our tutorial to learn how to install
Android 5.0 Lollipop N900XXUEBOK2 official firmware on GALAXY Note 3 SM-N900 follow this explanation to figure out how to install Samsung
official Firmware ROMs

 |How to update and install the firmware for Samsung phones by Odin /kiss/OTA|or
follow our tutorial in that page

You
can install Official ROM/Firmware update on your Android Samsung Galaxy
Phone by several ways as we shown below , so do one of the following
methods :

How To Install the Official ROM/Firmware via Samsung Kies and OTA (Over The Air) ?

Installing Official ROM/Firmware on Samsung Galaxy phones through PC via Samsung Kies ?

  1. Be sure that your PC is connected to the Internet , setup the Samsung Kies Utility , and connect your phone to your PC Via USB Cable .
  2. Run the Samsung Kies Utility and it will recognize your Samsung Phone.
  3.  On Samsung Kies Home Screen , you’ll see a notification say that a “New Firmware Upgrade is available” . If it said that “You have the latest Firmware update” it means that you didn’t have the latest Firmware on Kies yet ,So you can check back later, or try flashing this Firmware manually with (Odin).
  4.  Click the “Firmware Upgrade” to start the update process.
  5.  Follow the instructions that appear on the screen.
  6.  After finishing the updating process your Phone will reboot automatically.
  7. After the reboot you can disconnect your Phone from your PC.

Installing Official ROM/Firmware Android Lollipop on Samsung Galaxy through OTA (Over The Air) ?

  1. Connect your Android Phone to a Wi-Fi network or mobile data (Internet) and be sure to have a stable Internet connection (It is not recommended to use Mobile Data because of the high cost).
  2.  Go to Settings>About then click on Update or update option (if you received a message says that “The latest update have already been installed” and you do not receive any updates yet, try through Samsung kies , If not, do it with Odin manually)
  3. If you have a message “ New firmware update available “ Click OK to start the downloading and installation process.
  4. After finishing the updating process your Phone will reboot automatically.

Installing Official ROM/Firmware N900XXUEBOK2 Android 5.0Lollipop on GALAXY Note 3 N900 through Odin?

The previous methods for receiving Official ROM/Firmware
update SM-N900XXUEBOK2 Android 5.0Lollipop on your GALAXY Note 3 are the official methods, but most of us doing it with the manual
method through the Odin , So the following steps will show you how to do it
with Odin program .
  1. Install the Samsung USB driver .
  2.  Unzip the ROM file and
    you will have this file with this name N900UXXDLJ5_N900UODDDLI7_INU.tar.md5
    .
    It is the N900XXUEBOK2 Android 5.0 Lollipop Official
    ROM/Firmware update for Samsung GALAXY Note 3 SM-N900 open Odin .

    open Odin
  3. Now press the AP button
    and choose the ROM file with .tar.md5 that you just extracted it . See the
    following picture:


  4. Now we will get into the
    download mode  in your Samsung
    device . To enter the download mode do the following , Turn off the device
    and then press and hold this three buttons (volume down button + Home
    button + power button )
    .

    volume down button + Home button + power button
  5. You will have this alert as
    shown in the following picture, so press Volume Up button to continue .

    press Volume Up button to continue .
  6. After
    pressing the Volume Up button you are now on the download mode and ready for
    flashing. You will find a screen like the screen in the following picture .

    Volume Up button you are now on the download mode and ready for flashing
  7. Now
    you are already have the Samsung USB Driver and when you entered the Download
    Mode as shown in the previous picture, you can now connecting your Samsung
    GALAXY Note 3 SM-N900
    via USB Cable then you will find that your PC
    now is installing the device driver and recognizing it as shown in the
    following picture .

    installing the device driver and recognizing it as shown in the following picture

  8. Now Go back to Odin to see if
    the ID:COM box’s color
    turned into blue color or not, this blue color means that your Samsung
    GALAXY Note 3 SM-N900
    connected successfully and the Odin
    recognized it as shown in the following picture:

    see if the ID:COM box’s color turned into blue color or not, this blue color
  9. Make
    sure that the “Auto Reboot” and “F. Reset Time” options only are checked.

  10. Click
    on the Start button in Odin to start the
    flashing process. You will find the blue color progress bar then will turn into
    black with white square ( Don’t touch anything in the Odin program or in your
    phone and also don’t move your phone or the USB cable to avoid errors ). If the
    flashing process completed successfully you will find the PASS! Message with green
    background as shown in the following picture. It means that the operation
    completed successfully and now you can disconnecting your phone safely.

     If the flashing process completed successfully you will find the PASS!
  11. After
    installing that firmware your phone will reboot automatically and we can say to
    you now congratulations you have now the Official Firmware
    N900XXUEBOK2 Android 5.0 Lollipop on your Phone Samsung GALAXY Note 3 SM-N900.

    Another method :

    1. Download Android 5.0 N900XXUEBOK2 Firmware for GALAXY Note 3 SM-N900 from the previous download links.
    2. Download Odin V 3.10.7
    3. Switch off your Phone and enter
      the GALAXY Note 3 SM-N900 into Download Mode by
      pressing and holding the Volume Down + Home + Power buttons
      (long press until the boot screen appear), now press Volume Up key
      to proceed to Download Mode.
    4. Extract the downloaded Odin3.10.7 zip
      file and run the Odin3 v3.10.7.exe file as
      administrator
       (Right click on the .exe file and click on Run as
      administrator).
    5. Now connect your GALAXY Note 3 to your computer via USB cable.
    6. In Odin screen, you
      should see a COM Port number like “0:[COM7]” at ID:COM
      section and you will find a text appearing in the message box, it
      means that your device has been detected by Odin.
    7. Make sure that the “Auto
      Reboot”
       and “F. Reset Time” options only are
      checked.
    8. Now, extract the downloaded
      firmware zip file, you’ll find a firmware file with that extension .tar.md5
      .
    9. In Odin screen, click on PDA button
      and select the firmware file with the .tar.md5 extension (You
      will find the firmware file name looks like something like that : N900UXXDLJ5_N900UODDDLI7_INU.tar.md5.
    10. Now, click on the Start button
      to begin the installation process, wait for a few moments until the
      installation process completed.
    11. When the installation process
      is completed,  you will see the PASS! message with
      a green background appears in the ID:COM port.
    12. Your Phone will automatically
      reboots after installation process finishing.
    13. You can now disconnect your
      Phone from your PC safely .
    14. It’s done !!

    Solution Boot Loop

    If your device stuck in
    boot loop after installing the firmware update like N900XXUEBOK2 Official
    Firmware Android 5.0 Lollipop on GALAXY Note 3 SM-N900, then you can do
    the following method:

    If the Phone has stopped more than 15 minutes on the main
    boot screen or you see a screen of death as it known follow the following:

    1. Remove
      the battery from your phone.
    2. Power
      on your phone in the Recovery mode by pressing the next three
      buttons ( volume down button + home button + power
      button )
      .
    3. Now
      select Wipe Data/Factory Reset and Wipe Cache Partition. You can navigate
      inside Recovery mode by using the sound buttons. After finishing you should
      now click on reboot
    4.  Now
      the problem should fixed.     

    Guide to help you in installing
    Root on GALAXY Note 3 SM-N900 – N900XXUEBOK2 Android
    5.1.1 Lollipop.

    We
    also work at provides a detailed explanation of how the root N900XXUEBOK2 Android 5.0 Lollipop on Phone Samsung GALAXY Note 3 SM-N900 detailed explanation you the from the following link:
    Explain How to Get Root on Phone GALAXY Note 3 SM-N900 5.1.1 Lollipop
    In the absence of a special link to download root above this means that we will put in the nearest time

    Here is the topic has ended and has got the Official Firmware update for your device and also to root if availability.






    More About Model OR


    Leave a Reply

    avatar
      Subscribe  
    Notify of